Style Arc Romy Anorak

Image

The Style Arc Romy is an unlined anorak style coat that hits at the thigh. It has a front zip with inside and outside zipper guards, button closures at the pockets and collar, and tucks and a drawstring at the hem. The belt loops and belt are optional.

I made this as a replacement for my Safari Jane jacket. During actual wear I ran into a few problems with that particular project:

  • The upper back was very narrow, and I really noticed it when driving or wearing anything heavier than a tshirt under it. It was just uncomfortable to wear.
  • The water repellent coating completely disappeared during a wash, and I couldn’t seem to restore it. Anything heavier than a slight drizzle and I was getting wet.
  • The fabric was very light and didn’t press well, so the lining didn’t stay in place very well at the cuffs and hem.
  • The metal eyelets weren’t supported enough and started to rip through the lining.
  • The inside zipper pockets were a good idea in theory, but in practice I found them awkward. It required two hands to quickly stash something.
  • The hood felt like it didn’t project far enough in front and the front flaps were annoying. I never used them.

So for this project I decided to go with something that had a waterproof backing rather than depending on just the water repellent coating.

Recommended fabrics for the Romy are “soft” fabrics – silk, lighter weight wools, etc. I went with something that wasn’t soft at all: Ultrex. Ultrex is a nylon water resistant fabric with a waterproof and windproof polyurethane backing. I got my Ultrex from The Green Pepper. They strongly recommended lining it to protect the backing, so for that I used a lightweight nylon shirting I found in my stash. You do not want to go without a lining just because the backing feels nasty against the skin. It has a very rubbery feel. It was torture turning out the belt…

I got the best results with Ultrex when I used a medium low setting for pressing and light steam when absolutely necessary. For sewing it I used regular Gutermann Mara 100 thread, a Microtex needle, and a 3mm stitch for regular seams and 4mm stitch for topstitching.  I tried both a Teflon and walking foot and had better results with the walking foot. I treated it like leather and avoided ripping and resewing unless absolutely necessary because I wanted to avoid having pinholes in the backing. The only interfacing I used was when I made the reinforcement for the metal grommets – and in that case it was needlepunch, which is almost like a lightweight fleece.

I used quite a bit of hardware for this coat. My zipper was a #5 antique brass zipper. Instead of buttons I used size 20 snaps from Snap Source. The shock cord, hem toggles, and cord closures at the hem were from The Green Pepper. The “bean” style toggles I used for the hood were from a Thai ebay seller. Instead of buttonholes I used metal 00 grommets. To better support the grommets and prevent them from pulling through I made a “washer” for the grommets out of two layers of the needlepunch interfacing from The Green Pepper.

I wanted a secure way to hold my keys in place so I inserted a piece of 1″ nylon webbing into the inside of the pocket box pleat at the top, then sewed the other end to a black snap from The Green Pepper.

photo

My fitting adjustments were:

  •  Lengthened 1.25″ between bust and waist
  • 3/4″ broad back adjustment, including 3/8″ length
  • Lengthened the sleeves 1.25″
  • Added a total of 5″ to the lower hip
  • Added 3/4″ width to the sleeve at the upper arm/elbow

I should have rotated the shoulder dart as a forward shoulder adjustment as well, but I didn’t notice until it was too late.

I really wanted a hood to go with this. I have a larger than average size head (too many brains??) and most womens “one size fits all” hats and hoods are too small for me. I hate how most hoods don’t offer good coverage, especially when I have my hair up in a ponytail. I compared several hood patterns and decided that due to the wide collar the the best starting point was the Sewaholic Minoru. Instead of sewing the hood pieces together at the center back I made it shape my head a little bit better by adding a 4″ wide rectangular piece to the center back. I then topstitched the seams in place, then after I sewed in the lining I folded back the brim edge about 1″ and sewed in a casing for the shock cord because I wanted to be able to tighten it on windy days. I discovered from wearing my Safari Jane that I HATE having loose ends of shock cord around my face, so I used the bean style toggles that have two holes in them, threading the end of the shock cord so that it was caught at the bottom of the hood rather than sticking out through the grommet. Once again I used a metal eyelet instead of a buttonhole for the shockcord opening. It is a little tight with two pieces of cord going through it but I can still adjust it with some effort. To finish the hood I drafted a bottom facing out of Ultrex, sewing it to the bottom edge. I then folded back the seam allowance of the facing’s upper edge and edgestitched in place.

IMG_0869
Inside of hood

IMG_0868

After I finished the hood I added the collar and hood snaps. Note: the collar buttonhole placement on the pattern is correct but the button placement is not. The front fly guard is buttonholed but the buttons (or in my case, the bottom snaps) are actually placed on the collar and NOT on the bottom fly guard. (I confirmed this by looking at a RTW Land’s End down coat.)

IMG_0862

When trimming threads I accidentally nicked the lining by the center back collar. To fix it I dabbed on some Fray-Check and then sewed a Style Arc label over it. Doubles as a hanging loop!

IMG_0863

One thing I was really annoyed about was when I was snapping the hood to the anorak I noticed that the hood was a different color than the Romy! I had ordered the Ultrex for a coat last year and then a few months later ordered the Ultrex for the hood. The coat is a dark navy and the hood is a lighter navy. I’m not sure if it was a different dye job or if Ultrex comes in different shades of navy. I learned my lesson: when buying yardage for a coat/jacket + hood project make sure to buy it as one whole piece rather than going back and buying more later on!

Despite the navy mismatch I am very pleased with my Romy. It has a durable, high quality feel to it and all the design elements I wanted. It is a great replacement for my Safari Jane coat.

16 thoughts on “Style Arc Romy Anorak

  1. Well, this looks like a very professional and well thought out jacket! I, too, have found that inside pockets are great in theory, but not so much in practice. I never want to open my jacket and fish around in pockets. I sewed an extension for my keys into my small clutch, and it’s great never having to look for them, so that’s a great addition. Your jacket looks great on you, so I hope you enjoy it.

    Like

    1. The key clip in my tote has saved me many, many times from having to dig and dig looking for my keys. That’s why I definitely wanted to include it with this jacket!

      Like

  2. This is awesome. So practical and still somehow chic. It must have been quite a production. And I hear you on the hood being a diff shade. That would make me super mad (though I’m sure no one else will notice). BTW, love your comment about your big head being the potential by-product of too many brains! Let’s hear it for the smart girls. 🙂

    Like

    1. When I attached the hood to the jacket I went “SERIOUSLY??” I’m consoled by the fact that this is a rain jacket and therefore will not be worn on days with good visibility.

      My mom is the one that said I had too many brains. I told her “how do you know it isn’t like Jupiter – large but with nothing but a bunch of hot air inside?” 😉

      Like

  3. Did you prefer the Style Arc Romy to Sewaholic’s Minaru? You made reference to the hood from the latter, so I know you’re familiar with both. Your jacket looks great. Love your blog.

    Like

  4. Anne – did you have any issues with the instructions regarding the center front alignment? I made this coat last year, and while I LOVE the style, fit, and everything else – I thought the instructions for the zipper insertion caused the front placket alignment to be off center. I finally just did it so I thought it was correct by placing the left side of the zipper ON TOP of the placket – not in the seam between left placket and left front. Did you have any issue with this?

    Like

    1. I don’t remember having any issues…but I did use a Land’s End down jacket as my reference instead of the Style Arc instructions. That’s how I figured out the snaps/buttons on the collar are actually offset, not centered like shown in the line drawing.

      Like

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s